----------------------------------------------------- root@OpenWrt:/# firstboot && reboot This will erase all settings and remove any installed packages. Are you sure? [] y /dev/mtdblock5 is mounted as /overlay, only erasing files procd: - shutdown - root@OpenWrt:/# [ 162.390000] br-lan: port 2(wlan0) entered disabled state [ 162.400000] br-lan: port 1(eth0.1) entered disabled state [ 162.410000] device eth0.1 left promiscuous mode [ 162.420000] device eth0 left promiscuous mode [ 162.430000] br-lan: port 1(eth0.1) entered disabled state [ 162.470000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 162.520000] device wlan0 left promiscuous mode [ 162.530000] br-lan: port 2(wlan0) entered disabled state procd: - reboot [ 162.940000] Restarting system. U-Boot 1.1.3 (Oct 18 2013 - 15:39:39) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb4000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 29 spi device id: ef 40 17 0 0 (40170000) find flash: W25Q64BV raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.1.2.0 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Oct 18 2013 Time:15:39:39 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 Image Name: MIPS OpenWrt Linux-3.10.49 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1085179 Bytes = 1 MB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:50040 len:108efb Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 3.10.49 (pratik@ROBO) (gcc version 4.8.3 (OpenWrt/6 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is Asus RT-N14U [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bys [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa6 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jff2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0007c5b0 [ 0.000000] Readback ErrCtl register=0007c5b0 [ 0.000000] Memory: 61516k/65536k available (2433k kernel code, 4020k reserv) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] pinctrl core: initialized pinctrl subsystem [ 0.080000] NET: Registered protocol family 16 [ 0.110000] bio: create slab at 0 [ 0.110000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.120000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.130000] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.140000] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.150000] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.160000] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.170000] Switching to clocksource MIPS [ 0.180000] NET: Registered protocol family 2 [ 0.190000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.200000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.210000] TCP: Hash tables configured (established 512 bind 512) [ 0.230000] TCP: reno registered [ 0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260000] NET: Registered protocol family 1 [ 0.270000] rt-timer 10000100.timer: maximum frequncy is 2441Hz [ 0.300000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORI. [ 0.330000] msgmni has been set to 120 [ 0.340000] io scheduler noop registered [ 0.340000] io scheduler deadline registered (default) [ 0.360000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.380000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 1655A [ 0.390000] console [ttyS0] enabled, bootconsole disabled [ 0.390000] console [ttyS0] enabled, bootconsole disabled [ 0.420000] m25p80 spi32766.0: found s25fl064k, expected w25q128 [ 0.430000] m25p80 spi32766.0: s25fl064k (8192 Kbytes) [ 0.440000] 4 ofpart partitions found on MTD device spi32766.0 [ 0.450000] Creating 4 MTD partitions on "spi32766.0": [ 0.460000] 0x000000000000-0x000000030000 : "u-boot" [ 0.470000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.490000] 0x000000040000-0x000000050000 : "factory" [ 0.500000] 0x000000050000-0x000001000000 : "firmware" [ 0.510000] mtd: partition "firmware" extends beyond the end of device "spi30 [ 0.530000] 0x000000158f3b-0x000000800000 : "rootfs" [ 0.540000] mtd: partition "rootfs" must either start or end on erase block y [ 0.570000] mtd: device 4 (rootfs) set to be root filesystem [ 0.580000] mtd: partition "rootfs_data" created automatically, ofs=0x3a00000 [ 0.600000] 0x0000003a0000-0x000000800000 : "rootfs_data" [ 0.610000] ralink_soc_eth 10100000.ethernet (unregistered net_device): port) [ 0.630000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.640000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq5 [ 0.660000] rt3xxx-usbphy usbphy.3: loaded [ 0.670000] rt2880_wdt 10000120.watchdog: Initialized [ 0.680000] leds-gpio gpio-leds.4: pins are not configured from the driver [ 0.690000] TCP: cubic registered [ 0.700000] NET: Registered protocol family 17 [ 0.710000] Bridge firewalling registered [ 0.720000] 8021q: 802.1Q VLAN Support v1.8 [ 0.740000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.750000] Freeing unused kernel memory: 192K (802f0000 - 80320000) procd: Console is alive procd: - watchdog - [ 4.560000] usbcore: registered new interface driver usbfs [ 4.570000] usbcore: registered new interface driver hub [ 4.580000] usbcore: registered new device driver usb [ 4.600000] Button Hotplug driver version 0.4.1 [ 4.610000] rt2880-pinmux pinctrl.1: pin 1 is not set to gpio mux [ 4.620000] rt2880-pinmux pinctrl.1: request() failed for pin 1 [ 4.630000] rt2880-pinmux pinctrl.1: pin-1 (pio:1) status -22 [ 4.640000] gpio-keys-polled gpio-keys-polled.5: unable to claim gpio 1, err2 [ 4.660000] gpio-keys-polled: probe of gpio-keys-polled.5 failed with error 2 [ 4.670000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.690000] ehci-platform: EHCI generic platform driver [ 4.900000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled [ 4.910000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz [ 4.920000] ehci-platform 101c0000.ehci: EHCI Host Controller [ 4.930000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bu1 [ 4.950000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 4.980000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 4.990000] hub 1-0:1.0: USB hub found [ 5.000000] hub 1-0:1.0: 1 port detected [ 5.010000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.020000] ohci-platform 101c1000.ohci: Generic Platform OHCI Controller [ 5.030000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bu2 [ 5.050000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 5.120000] hub 2-0:1.0: USB hub found [ 5.130000] hub 2-0:1.0: 1 port detected [ 5.140000] Error: Driver 'gpio-keys-polled' is already registered, aborting. procd: - preinit - [ 5.600000] 8021q: adding VLAN 0 to HW filter on device eth0 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level jffs2 is ready No jffs2 marker was found [ 9.050000] jffs2: notice: (305) jffs2_build_xattr_subsystem: complete build. switching to overlay procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 10.680000] NET: Registered protocol family 10 [ 10.700000] nf_conntrack version 0.5.0 (964 buckets, 3856 max) [ 10.710000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 10.760000] Loading modules backported from Linux version master-2014-05-22-a [ 10.770000] Backport generated by backports.git backports-20140320-37-g5c33d0 [ 10.790000] Error: Driver 'gpio-keys' is already registered, aborting... [ 10.810000] Error: Driver 'gpio-keys-polled' is already registered, aborting. [ 10.830000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.880000] xt_time: kernel timezone is -0000 [ 10.920000] cfg80211: Calling CRDA to update world regulatory domain [ 10.930000] Error: Driver 'gpio-keys' is already registered, aborting... [ 10.940000] cfg80211: World regulatory domain updated: [ 10.950000] cfg80211: DFS Master region: unset [ 10.960000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_ga) [ 10.980000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 ) [ 11.000000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 ) [ 11.010000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 ) [ 11.030000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000) [ 11.050000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000) [ 11.060000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000) [ 11.080000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 ) [ 11.090000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0) [ 11.110000] Error: Driver 'gpio-keys-polled' is already registered, aborting. [ 11.180000] PPP generic driver version 2.4.2 [ 11.190000] NET: Registered protocol family 24 [ 11.210000] Error: Driver 'gpio-keys' is already registered, aborting... [ 11.230000] Error: Driver 'gpio-keys-polled' is already registered, aborting. [ 11.260000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 d [ 11.280000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected [ 11.300000] Error: Driver 'gpio-keys' is already registered, aborting... [ 11.320000] Error: Driver 'gpio-keys-polled' is already registered, aborting. [ 17.860000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 17.880000] device eth0.1 entered promiscuous mode [ 17.890000] device eth0 entered promiscuous mode [ 17.900000] br-lan: port 1(eth0.1) entered forwarding state [ 17.910000] br-lan: port 1(eth0.1) entered forwarding state [ 19.910000] br-lan: port 1(eth0.1) entered forwarding state [ 21.040000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 21.060000] device wlan0 entered promiscuous mode procd: - init complete - [ 21.510000] br-lan: port 2(wlan0) entered forwarding state [ 21.520000] br-lan: port 2(wlan0) entered forwarding state [ 21.530000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 23.520000] br-lan: port 2(wlan0) entered forwarding state